RR 125 gal Tank Stand and Canopy

[Rychek]

I have a Reef Ready 125 gallon tank, stand and canopy that I need to sell. Tank dimensions are 72"x24"x17" (not your typical 125 gal footprint). The stand is custom (heavy, but sturdy) and tall (~42" tall). A full size pickup would be needed to transport.
This is a three part set. Will not part out.

For more details on the tank, see my thread here (http://www.maast.org/showthread.php?59200-125-gal-Predatory-Community-(formerly-Loach-Lounge))

Known Cons/issues
The tank has a few scratches on the left hand side of the face.
Tank has blue paint on right end on the outside (a razor blade or paint remover should take it right off)
Stand is missing a panel on the right end, but I have plywood covering the hole.
I removed the two center braces as they were not strictly necessary in a tank this shallow.

Tank, Stand, Canopy $300 (or trade for non-RROD Xbox360 or a PS Vita).

Located in the North West Crossing area of San Antonio.
Shipping not available.

Pics for easier viewing (please note that the sumps pictured are not included or available):

http://i212.photobucket.com/albums/cc246/Rychek426/IMG_5952.jpg
http://i212.photobucket.com/albums/cc246/Rychek426/IMG_5951.jpg
http://i212.photobucket.com/albums/cc246/Rychek426/IMG_5950.jpg
http://i212.photobucket.com/albums/cc246/Rychek426/FTSFlash-1.jpg
http://i212.photobucket.com/albums/cc246/Rychek426/TankStandSump.jpg
http://i212.photobucket.com/albums/cc246/Rychek426/IMG_5947.jpg

[KING]

pics?

[SABOB]

Pictures?


Sent from my iPhone using Tapatalk

[SinisterLou]

:thumbs_up:Pics are on his link to his build thread

[Rychek]

Indeed, the pics are in the build thread. I'll see if I can scrounge up some others.

[Rychek]

posted pics.

[BBQHILLBILLY]

How wide of a sump can you put inside the stand and what type of paint do you have on the stand/canopy?

[Rychek]

The widest sump that will fit through the hole in the end is 18". At one point I had a 75 gal tank in there as a sump.

[BBQHILLBILLY]

Can your stand hold the weight of a 180 or 210?

[Rychek]

Yes. It will hold anything with a 6'x2' base. It is a very stout 2"x4" frame.

[BBQHILLBILLY]

Im assuming you have 2 holes drilled on the bottom corner. What size are they and do you have bulkheads and any plumbing?

[Rychek]

Yeah, two holes. 2" drain and a 1.5" return (I think. Will measure after the kids are in bed). I have all of the bulk heads and plumbing, though I can't get the drain bulkhead off. However, it still works.

[Rychek]

I was off a bit on the plumbing sizes. The drain pip is 1.5" PVC and the return is 3/4" PVC. The holes are themselves are larger to accommodate the bulkheads.

[Rychek]

I was off a bit on the plumbing sizes. The drain pip is 1.5" PVC and the return is 3/4" PVC. The holes themselves are larger to accommodate the bulkheads. Also, the drain pipe under the tank from the bulkhead to the end of the line has a large valve to close it off and three smaller valves the could be useful for running a reactor or protein skimmer via gravity. I haven't tried it myself as it was a fresh water tank, but it has potential.